Видео

Chevy small block 450hp V8 quite fast for lightweight truck

WOW! I didn't know you could press it in without square

The 8 track! Loved the way it would change channel right in the middle of a song!!!!!!

gasket sealer??

I put a pint of brake fluid in a crankcase with 5.5 quarts new motor oil. Do you think that will do anything bad for 5,000 miles?

Hey bud. Great channel Can i use the product to clean catalytic converter

Wow, amazing how dirt comes off with a power washer

My 2000 Nissan Maxima keeps losing rpm’s. Had the throttle body cleaned twice. It works for awhile okay but eventually the rpm’s goes below 1000, the 500 and eventually it stalls. Hope this is the answer

Ty I appreciate it I will try ❤

Thank you so much for putting this video out! It really helped me!

It's called SURVIVAL! Only the rams can SURVIVE! WSSU! HBCU!!

I just bought the high pressure pump and mine didnt come with the cup you put on that was wore out do you have to buy that separate?

Yo before you removed your rocker arms did you have too set your pulley or piston at TDC before removal of rockers nobody mentions that part or just remove rocker arms and reinstall them the same way and torque them down 22ftlbs and you'll be fine that way with no damage to push rods ?

Idiot

Thank you so much I'm going to Dollar Tree tomorrow and getting this and doing it to my grimey white van! I'm gonna lightly pressure wash the stuff off. No wiping it LOL

Did the car crank but didn’t turn in right? How did it do when you try to turn it on?

I would have put seafoam in the crank case not this stuff

Terrible video

Where could I get the torque specifications paperwork on a 09 chevy tahoe flex fule???

What kinda marker do you mark them with???

wow this kid is so smart i like the way he explained the whole proccess !!

Wow $25 is definitely a super great deal i got mine from Ollies in 2020 for 89 dollars. If you look it yup this Air fryer is worth a little over $200 dollars 😂

How many minutes of idling the car???

Anyone know what size are the bolts?

Where did you order your gaskets from?

how much dose a job like will charge

Other videos found that Stuff doesn't work. Need a couple Cases of Brake cleaner to Do even a small 4 cyl engine.

Super man❤

This is very bad for the engine

Very bad for the barrier

The wire brush on the drill risky

Where can I get the part from?

What year Chevy you working on here?

Thank you

This video was excellent

Two quarts transmission fluid then your two or three quarts of oil. Run motor till it gets hot. Shut off, and drain. Repeat, until oil is clean

Sealing surfaces on concrete? Is that really a good idea?

Could you post a step by step? This is what I got {Guessing that engine is 5 quarts of oil?} Flushing the vehicle 6 times process: Pre-Flush: Step 0 First flush: Steps 1, 3-6 Flushes 1-5: Steps 2-6 Clean Flush (6): Steps 2A, 4-9 Final Oil Change: 1B-2B, 4-5 Done Flushing Steps: 0) Clean the cylender heads (L/R) of large gunk / debris . . . Step 1) Remove 2 quarts of oil [first flush only] . . . Step 2) Add 3 quarts of engine oil [recap engine oil] Step 3) Add 2 quarts of cleaner, [40% mix 3:2 ratio, replace engine oil cap] Step 4) Start vehicle and idle for 5 minutes. [Listen for new noises, vibrations; dash warnings, leaking oil, stop and move to next step] Step 5) Wait 5 minutes for oil to settle and cool Step 6) Drain Oil [open engine oil cap, wait for clumps to stop flowing, replace darin bolt] . . . Step 7) Unstill old oil filter Step 8) Prime New Oil Filter [fill halfway with new oil, coat gasket with new oil] Step 9) Install new Filter . . . Step 2A) Add 5 quarts of engine oil [recap engine oil] . . . Step 1B) Add 1 quart (32floz) of Marvel Mystery Oil Step 2B) Add 4 quarts of engine oil [recap engine oil

Did you take apart the head or just scrape what you could get at?

Would help to know what year this is.

Welp thats enough youtube for the night!

Pretty clear appreciate

Bro good work!! My first time working on my car and this definitely helped. Appreciate your videos!!

So similar far as the oil screen and removing debris

I never seen a video i had my mechanic thats the best I've ever seen i worked beside him at previous job buy ne wayz had a old ford that the oil pump wasn't pumping he told me to run chem dip through the dip stick remove fuel pump relay turn over let sit etc and then through dip stick run water hose until the water comes out of oil pan clear .then fill oil and had 45+ lbs of pressure idling

Can I call someone to ask a question about this?

replacement of Water Pump went smoothly; but antifreeze empties from system as soon as I start engine up; in frustration, I call a mechanic I know (& use) at that point to see what is happening; he replies that the new pump must be defective; I can't see exactly where the antifreeze is leaking from, but it appears it's coming from directly behind or below the new pump; I noticed that there is a weep hole in pump housing directly above the lower right bolt; he replied that the fluid will escape through this weep hole if the pump is defective; I am taking the pump back to exchange it, but can you explain how the fluid will flow through that weep hole; I am confused on how that happens ( & frustrated that I have to do this replacement again;)

Hi I have a lot of oil on my van can you please let me know how to clean the top of the ingine with thick oil 🛢 thanks

What did he use

Judging by those prices it musta been before the Joe Biden “build back better” economy!.